Nugen Nugen S150PS Operator'S Maintenance Manual Download Page 36

Page: 36 / 39

OPERATOR & MAINTENANCE MANUAL

Warning:



To obtain an accurate reading, ensure the generator is level before checking the oil
level.



Do not overfill the engine oil. The level is not to exceed the upper limit. Excessive
engine oil may damage the engine.



Extinguish all naked flames and cigarettes before adding engine oil.

6.6 Fuel Filter

6.6.1 Drain water / sediment in the fuel filter

①

Loosen the drain plug to drain water and sediment.

②

Bleed the air and tighten plug.

6.6.2 Change fuel filter

①

Loosen the drain plug and drain fuel and water.

②

Loosen and remove fuel filter.

③

Add fuel into a new fuel filter.

④

Lubricate the new gasket with oil.

⑤

Screw the new filter into place and tighten
accordingly.

Danger:

Do not smoke whilst refuelling an engine. Do not refuel an engine near open flames
or sparks. Always stop the engine before refuelling.

Wear protective gloves, goggles and clothing whilst changing the fuel filter.

Summary of Contents for Nugen S150PS








































Search results

Summary of Contents for Nugen S150PS

Reviews:

Related manuals for Nugen S150PS

Brands by name

Popular brands

Nugen Nugen S150PS, Operator'S Maintenance Manual

Search results

Summary of Contents for Nugen S150PS

Reviews:

Related manuals for Nugen S150PS

Brands by name

Popular brands