background image

OPERATOR & MAINTENANCE MANUAL

 

9

 

 

2.7 Safety Labels 

Label 

Description 

 

1. Read the Operator’s Manual. 
2. No sparks or naked flames near the machine. 
3. Press the emergency stop switch when an 

emergency occurs. 

4. Do not disassemble the machine. 

 

Warning 

1. Wear hearing protection to prevent hearing loss. 
2. Avoid spraying water into the generator. 
3. Avoid hand injury in rotating belts and pulleys. 
4. Mechanical moving parts can cause   
    severe injury. 
 

 

Safety Instructions 

Read the Safety Instructions before operation. 

 

Warning 

Electric shock will cause serious injury or death.

 

 

Warning 

Escaping  steam  can  cause  severe  burns.    Never 
remove the pressure cap while the engine is warm or 
hot.    Always  allow  the  engine  to  cool  before 
removing the pressure cap. 

 

Warning 

Always refuel with the engine stopped and in a well 
ventilated  area.    Do  not  smoke  or  allow  naked 
flames  or  sparks  in  or  near  the  area  where 
refuelling is performed or where fuel is stored.

 

 

Warning 

Do  not  operate  whilst  transporting.    Ensure  panel 
latches  and  caps  are  secure  for  transporting  or 
relocating.

 

Summary of Contents for Nugen S150PS








































Reviews: