manualshive.com logo in svg

NR Electric PCS-9785, Instruction Manual, Page: 60 / 108

Share
Download
NR Electric PCS-9785 Instruction Manual Download Page 60

6 Settings 

 

PCS-9785 Satellite Synchronized-Clock

 

6-6 

Date: 2019-07-05 

No. 

Item 

Range(Unit) 

Default Value 

23 

Destination_3 

000.000.000.000~255.255.255.255 

000.000.000.000 

24 

Genmask_3 

000.000.000.000~255.255.255.255 

255.255.255.000 

25 

Gateway_3 

000.000.000.000~255.255.255.255 

000.000.000.000 

26 

Destination_4 

000.000.000.000~255.255.255.255 

000.000.000.000 

27 

Genmask_4 

000.000.000.000~255.255.255.255 

255.255.255.000 

28 

Gateway_4 

000.000.000.000~255.255.255.255 

000.000.000.000 

29 

IP_FE1 

000.000.000.000~255.255.255.255 

000.000.000.000 

30 

IP_FE2 

000.000.000.000~255.255.255.255 

000.000.000.000 

31 

IP_FE3 

000.000.000.000~255.255.255.255 

000.000.000.000 

32 

IP_FE4 

000.000.000.000~255.255.255.255 

000.000.000.000 

33 

Port_UDP_Meas_f_Grid 

0~65535 

7500 

34 

t_Send_UDP_Meas_f_Grid  1~60(s) 

1(s) 

 

IP_LAN1, IP_LAN2, IP_LAN3, IP_LAN4 

IP address of Ethernet port 1, 2, 3 or 4. 

 

Mask_LAN1, Mask_LAN2, Mask_LAN3, Mask_LAN4 

Subnet mask of Ethernet port 1, 2, 3 or 4. 

 

En_LAN2, En_LAN3, En_LAN4 

Enable/Disable Ethernet port 2, 3 or 4. 

The Ethernet port 1 is always in service. 

 

Opt_NetMode 

Network mode option 

Normal: Normal network (not ring) 

PRP: Parallel Redundancy Protocol 

HSR: High-availability Seamless Redundancy 

RSTP: Rapid Spanning Tree Protocol 

 

Cfg_RingNet1, Cfg_RingNet2 

Use these settings to set two Ethernet ports in station level ring network. 

The value of these settings represents a 4-bits binary number. Each bit represents a 
corresponding Ethernet port's ring-network status. Use the following map to decide the 
specific setting value. Additionally, the default value "0" means the ring network mode is 
deactivated. This device works in STP mode. 

08020

08020

08020

08020

08020

08020

08020

08020

08020

Summary of Contents for PCS-9785













































































































Reviews:

No comments