NR Electric PCS-9785 Instruction Manual Download Page 30 | Manualshive

Page: 30 / 108

NR Electric PCS-9785 Instruction Manual Download Page 30

4 Supervision

PCS-9785 Satellite Synchronized-Clock

4-2

Date: 2019-07-05

No.

Item

Description

14 Alm_Parity_IRIG-B2

Error is found during the parity check of IRIG-B2

15 Alm_Recv_IRIG-B1

The reception of IRIG-B1 is invalid

16 Alm_Recv_IRIG-B2

The reception of IRIG-B2 is invalid

17 Alm_Send_IRIG-B

The sending of IRIG-B signal is invalid.
The CLK module is failed.

18 PTP1.Alm_Conflict_ID_Clk An identical clock exists on the Precision Time Protocol (PTP) network1.
19 PTP2.Alm_Conflict_ID_Clk An identical clock exists on the Precision Time Protocol (PTP) network2

Table 4.1-2 Troubleshooting

No.

Item

Suggestion

1

Fail_Device

Inform the service agency for repair.

2

Alm_Initialization

Check external time source if the initialization failure has lasted for a long
period.

3

Alm_Device

Eliminate all the other alarms firstly.

4

Alm_DualDev

Verify the setting "Opt_DualDev" along with the device hardware.

5

Alm_Pwr1_Device

Check the rated input voltage and the PWR module 1.

6

Alm_Pwr2_Device

Check the rated input voltage and the PWR module 2.

7

Alm_Receiver_SatlCh1

Inform the service agency for repair.

8

Alm_Receiver_SatlCh2

Inform the service agency for repair.

9

Alm_SynLoss_SatlCh1

Check the wiring between the antenna 1 and the CLK module.

10 Alm_SynLoss_SatlCh2

Check the wiring between the antenna 2 and the CLK module.

11 Alm_Ant_SatlCh1

Check the antenna 1 installation and its connection with the CLK module.

12 Alm_Ant_SatlCh2

Check the antenna 2 installation and its connection with the CLK module.

13 Alm_Parity_IRIG-B1

Unify the parity check mode of both TX & RX for the IRIG-B1 link.

14 Alm_Parity_IRIG-B2

Unify the parity check mode of both TX & RX for the IRIG-B2 link.

15 Alm_Recv_IRIG-B1

Check the optical fiber connection for the IRIG-B1 reception link.

16 Alm_Recv_IRIG-B2

Check the optical fiber connection for the IRIG-B2 reception link.

17 Alm_Send_IRIG-B

Check the optical fiber connection for the IRIG-B sending link.
Check the CLK module.

18 PTP1.Alm_Conflict_ID_Clk

Check the IDs of all the clocks who are on the same PTP network.
PTP1: the network connected to the second optical port from the bottom of the
MON module
PTP2: the network connected to the last optical port of the MON module

19 PTP2.Alm_Conflict_ID_Clk

08020

08020

08020

08020

08020

08020

08020

08020

08020

«
...
28
29
30
31
32
...
»

Summary of Contents for PCS-9785













































































































Reviews:

No comments