NR Electric PCS-9785 Instruction Manual Download Page 43

Page: 43 / 108

5 Hardware

PCS-9785 Satellite-Synchronized Clock

5-11

Date: 2014-10-15

NR1216A

Figure 5.6-3 COM Module (NR1216A)

Table 5.6-4 Pin definition of NR1216A

Pin No.

Symbol

Description

OUT1+

The positive pole of the No.1 output contact

OUT1-

The negative pole of the No.1 output contact

GND

The ground for shielding

OUT2+

The positive pole of the No.2 output contact

OUT2-

The negative pole of the No.2 output contact

OUT3+

The positive pole of the No.3 output contact

OUT3-

The negative pole of the No.3 output contact

GND

The ground for shielding

OUT4+

The positive pole of the No.4 output contact

OUT4-

The negative pole of the No.4 output contact

OUT5+

The positive pole of the No.5 output contact

OUT5-

The negative pole of the No.5 output contact

GND

The ground for shielding

OUT6+

The positive pole of the No.6 output contact

OUT6-

The negative pole of the No.6 output contact

OUT7+

The positive pole of the No.7 output contact

OUT7-

The negative pole of the No.7 output contact

GND

The ground for shielding

OUT8+

The positive pole of the No.8 output contact

OUT8-

The negative pole of the No.8 output contact

08020

Summary of Contents for PCS-9785













































































































Search results

Summary of Contents for PCS-9785

Reviews:

NR Electric PCS-9785, Instruction Manual, Page: 43 / 108

Search results

Summary of Contents for PCS-9785

Reviews: