background image

Operating manual 

LTSA LTMA

2.

The specified order must be followed!

Special note for action that must be performed.

• Enumeration of features
• Other feature

EXPERTS

The Experts symbol identifies activities that are reserved exclusively for qualified and specially

trained personnel.
 

Warning Notes

Warning notes are specially highlighted::

WARNING!
Warning notes with the signal word WARNING refer to risks that can result in severe

or fatal injuries! The note contains safety measures to protect affected persons.
► Instructions must be followed without exception.

CAUTION!
Warning notes with the signal word CAUTION refer to risks that can result in

property damage or personal injury (minor injuries). The note contains instruc-

tions for preventing damage.
► Instructions must be followed without exception.

Illustrations

Illustrations appear in the text where required. References to the illustrations are shown in brackets, if

necessary (see table).

Reference to illustration

Application

none

• Only one illustration

• Reference to the illustration is obvious

• No position number in the illustration

(A)

• Only one illustration

• Reference to the illustration is obvious

• Position number in the illustration

(see fig. above)

• Several illustrations

• No position number in the illustration

(see fig. above, pos. A)

• Several illustrations

• Position number(s) in the illustration

Table 1: Differenet references to illustrations.

Parameters

Parameters in the parameter menu are represented in the format 

Menu name

 > 

Parameter name

 in

grey type.

Edition 02 - 7/2021

4

Please note!

General Information

Summary of Contents for LTMA

































Reviews: