background image

170

 / Programming Hunt Groups

Compact ICS 7.1 System Coordinator Guide

N0130955  01

6.

Press 

®

 to exit or 

 to continue programming.

Setting the hunt delay

This setting allows you to program the number of rings the system permits 
at a Hunt Group set before moving on to the next telephone in the Hunt 
Group.

1.

At 

Hunt groups

, press 

. The display shows

 

Show group

.

2.

Enter the Hunt Group number you want to program (1-6) or press 

 to scroll through the groups.

3.

Press 

. The display shows 

Member DNs:

.

4.

Press 

 until the display shows 

Hunt delay

.

5.

Press 

CHANGE

 to select the setting: 

1, 2, 3, 4, 5, 6, 7, 8, 9, 10

.

6.

Press 

®

 to exit or 

 to continue programming.

Programming busy line setting

A Hunt Group is considered busy if either of these two scenarios exist:

all of its members are being presented an incoming Hunt Group call

all of its members are active on a Hunt Group call

There are three routing options if all members are busy:

BusyTone—the caller gets a busy tone

Overflow—the call is routed to an overflow position

Queue—the call stays in the system for a period of time. Within this 
period of time, the call is presented to a member if one becomes 
available. When the time-out occurs, the call is presented to an 
overflow position.

1.

At 

Hunt groups

, press 

. The display shows

 

Show group

.

2.

Enter the Hunt Group number you want to program (1-6) or press 

 to scroll through the groups.

3.

Press 

. The display shows 

Member DNs:

.

4.

Press 

 until the display shows 

If busy:

.

Summary of Contents for Compact ICS 7.1











































































































































































































































































Reviews: