Nortel AN Series Configuration Manual Download Page 87

Page: 87 / 142

Managing ANH Repeater Ports

308614-14.20 Rev 00

5-5

Testing and Resetting ANH Repeater Ports

You can use Site Manager to test and reset ANH repeater ports.

Site Manager Procedure

You do this

System responds

1. In the Site Manager main window, choose

Tools

The Tools menu opens.

2. Choose

Configuration Manager

The Configuration Manager menu opens.

3. Choose

Dynamic

The Configuration Manager window
opens, displaying the real-time router
hardware and software configuration.

4. Choose

Platform

The Platform menu opens.

5. Choose

Setup Repeater

The Setup Repeater menu opens.

6. Choose

Group Parameters

The Group Parameters window opens.

7. Set the following parameters:

•

Reset

•

Selftest

Click on

Help

or refer to the parameter

descriptions beginning on page A-9.

The Configuration Manager tests each
repeater port and indicates in a log file
whether the ports pass the diagnostics.

8. Click on

Site Manager executes the action(s)
specified in the Group Parameters
window and then closes the window.

Note:

The repeater port self-test does not disrupt traffic flow. Resetting a

repeater port does disrupt traffic flow; however, it does not affect the
management counters defined in the RFC 1516 MIB specification.

Summary of Contents for AN Series















































































































































Search results

Summary of Contents for AN Series

Reviews:

Nortel AN Series, Configuration Manual, Page: 87 / 142

Search results

Summary of Contents for AN Series

Reviews: