Nortel AN Series Configuration Manual Download Page 129

Page: 129 / 142

Using the Quick-Start Local Boot Procedure

308614-14.20 Rev 00

C-11

Frame Relay Worksheet

Prompt

Options

Your Response

Enter Management type [3]:

1. DLCMI None
2. Rev 1 LMI
3. ANSI T1 617D
4. CCITT Annex A
5. LMI Switch
6. Annex D Switch
7. Annex A Switch

Enter addressing type [4]:

1. ADDR Q.921
2. ADDR Q.922 (MARCH ’90)
3. ADDR Q.922 (NOVEMBER ’90)
4. ADDR Q.922

Enter address field length

[2]:

2. Two Bytes
3. Three Bytes
4. Four Bytes

Enter DLCI number [30]:

(For DLCMI None, LMI Switch, Annex D
Switch, and Annex A Switch only)

Enter the permanent virtual circuit
(PVC) number.

Note:

The valid range for the DLCI

number is 16 to 1007.

PPP Worksheet

Prompt Options

Your

Response

Enter Remote IP address in

dotted decimal notation:

Enter the IP address of the peer
connection.

Do you wish to turn on the PPP

echo function? (y/n) [n]:

y(es)
n(o)

Enable PAP (Password

Authentication Protocol)?

(y/n) [n]:

y(es)
n(o)

Note:

If you answer y(es), the script

requests a PAP ID and password for
this interface. If you answer n(o), it
prompts you to enable CHAP.

(continued)

Summary of Contents for AN Series















































































































































Search results

Summary of Contents for AN Series

Reviews:

Nortel AN Series, Configuration Manual, Page: 129 / 142

Search results

Summary of Contents for AN Series

Reviews: