Nortel AN Series Configuration Manual Download Page 19

Page: 19 / 142

308614-14.20 Rev 00

1-1

Chapter 1

Understanding Tools and Options

The AN/ANH and ARN families of routers connect multiprotocol workgroups to
corporate backbone networks. This chapter provides an overview of the software
and procedures for configuring and managing router remote access for AN, ANH,
and ARN routers.

Network Configuration and Management Tools

There are several tools available for configuring and managing the AN/ANH, and
ARN routers:

•

Graphical, SNMP-based network management tools within
Optivity Internetwork

™

, a component of the Nortel Networks

Optivity Enterprise

™

application suite:

Site Manager, a router management, configuration, and monitoring
application

RouterMan

™

, a real-time router performance and status reporting

application

PathMan

™

, a diagnostic application for determining the complete data

path between two network devices

Topic

Page

Network Configuration and Management Tools

1-1

Router Startup Procedure

1-2

Preparing for the Initial Startup

1-13

Selecting the Routine Startup Option

1-16

Steps for Completing Startup Options

1-18

Summary of Contents for AN Series















































































































































Search results

Summary of Contents for AN Series

Reviews:

Nortel AN Series, Configuration Manual, Page: 19 / 142

Search results

Summary of Contents for AN Series

Reviews: