manualshive.com logo in svg

Nortel AN Series, Configuration Manual, Page: 58 / 142

Share
Download
Nortel AN Series Configuration Manual Download Page 58

Configuring Remote Access for AN and Passport ARN Routers

3-4

308614-14.20 Rev 00

Table 3-3

 lists the optional 

expansion modules

 available for an ARN. An 

expansion module is a parallel daughterboard installed on the base module. The 
ARN base module supports only one expansion module.

Table 3-4

 lists the optional 

adapter modules

 for an ARN. An adapter module is a 

serial daughterboard installed in the front-panel card cage. The ARN base module 
supports one or two adapter modules.

Table 3-3.

ARN Expansion Module Configurations  

Expansion Module

Site Manager Module Name

Ethernet

Ethernet

Ethernet with DCM

Ethernet/DCM

Token Ring

Token Ring 

Tri-Serial

TRI Serial

Ethernet/Tri-Serial

Ethernet/TRI Serial

Ethernet/Tri-Serial with DCM

Ethernet/TRI Serial/DCM

Token Ring/Tri-Serial

Token Ring/TRI Serial

Table 3-4.

ARN Adapter Module Configurations  

Adapter Module

Site Manager Module Name

Serial

Serial

ISDN BRI S/T 

ISDN ‘S/T’

ISDN BRI U

ISDN ‘U’

56/64K DSU/CSU*

* The ARN supports network booting over DSU/CSU interfaces only for the default 

configuration, 56 Kb/s DDS lines. You cannot netboot over a 64 Kb/s DSU/CSU 
interface.

56/64K DSU/CSU

V.34 Modem

V34 Modem

X.25 PAD

X25 PAD

FT1/T1 DSU/CSU

Fractional T1

FE1/E1 G703

Fractional E1

Summary of Contents for AN Series















































































































































Reviews:

No comments