manualshive.com logo in svg

Nortel AN Series, Configuration Manual, Page: 38 / 142

Share
Download
Nortel AN Series Configuration Manual Download Page 38

Configuring Remote Access for AN and Passport ARN Routers

1-20

308614-14.20 Rev 00

Netboot

Complete the following steps for the Netboot option:

1.

Use the Configuration Manager in local mode to create a complete 
configuration file for the AN/ANH or ARN router. (See Chapter 3 and 

Configuring and Managing Routers with Site Manager

.)

2.

Set up a UNIX workstation on the network to support BootP. (See Chapter 2.)

3.

Use Site Manager to enable BootP on each router interface between the router 
and the BootP server. (See Chapter 3.)

4.

Ensure that there is a network connection from a synchronous, Ethernet, or 
token ring (ARN only) interface on the AN/ANH or ARN router to the 
upstream router.

5.

Install the kernel and application files in the BootP server’s file system, and 
make sure that they reside in the same directory. (See Chapter 2.)

6.

The person at the AN/ANH or ARN router site establishes a Technician 
Interface session, or you establish a session using a modem. (See the hardware 
installation guide.)

7.

The person at the AN/ANH or ARN router console uses the 

bconfig

 and 

ifconfig

 commands to configure a synchronous, Ethernet, or token ring (ARN 

only) interface. (See Chapter 4 and the hardware installation guide.)

8.

The person at the AN/ANH or ARN router site boots the router. (See the 
hardware installation guide.)

After the AN/ANH or ARN router boots, it obtains at least one startup file 
from the BootP server. If the configuration file meets your network 
requirements, the router starts bridging and routing traffic. 

9.

Use the Site Manager Statistics Manager and Events Manager tools to verify 
that the AN/ANH or ARN router is routing traffic as specified in the 
configuration file. (See 

Configuring and Managing Routers with Site 

Manager

.)

Note: 

 If the AN/ANH or ARN router will connect to the upstream router over 

a frame relay circuit, ensure that the upstream router is running BayRS Version 
7.71 or later.

Summary of Contents for AN Series















































































































































Reviews:

No comments