manualshive.com logo in svg

Nortel AN Series, Configuration Manual, Page: 84 / 142

Share
Download
Nortel AN Series Configuration Manual Download Page 84

Configuring Remote Access for AN and Passport ARN Routers

5-2

308614-14.20 Rev 00

Enabling and Disabling ANH Repeater Ports

You can use Site Manager to enable or disable the ANH repeater ports.

Site Manager Procedure

You do this

System responds

1. In the Site Manager main window, choose 

Tools

.

The Tools menu opens.

2. Choose 

Configuration Manager

.

The Configuration Manager menu opens.

3. Choose 

Dynamic

.

The Configuration Manager window 
opens, displaying the real-time router 
hardware and software configuration.

4. Choose 

Platform

.

The Platform menu opens.

5. Choose 

Setup Repeater

.

The Setup Repeater menu opens.

6. Choose 

Port Status

.

The Port Status window opens, allowing 
you to enable or disable the ports on the 
router.

Figure 5-1

 shows the Port Status window 

for the 8-port ANH. 

Figure 5-2

 shows the 

Port Status window for the 12-port ANH.

7. To change the status of a port, click on 

Enabled

 or 

Disabled

 to the right of the 

port number.

8. Click on 

OK

.

Site Manager closes the Port Status 
window and saves your changes.

Summary of Contents for AN Series















































































































































Reviews:

No comments