manualshive.com logo in svg

Nortel AN Series, Configuration Manual, Page: 102 / 142

Share
Download
Nortel AN Series Configuration Manual Download Page 102

Configuring Remote Access for AN and Passport ARN Routers

B-4

308614-14.20 Rev 00

Router Not Sending BootP Responses

If a router between the AN/ANH or ARN router and the BootP server is receiving 
BootP requests but is failing to send BootP responses, do the following:

1.

Use Site Manager to ensure that the BootP relay agent forwarding table 
associated with the router shows an IP address that is configured on the 
IP router. 

2.

Ensure that the input IP address is correct. If the Hops count is lower 
than the router’s position in the path, increase the Hops count.

For instructions, see “Creating the BootP Client Interface Table” on 
page 3-14.

3.

Use the Configuration Manager to ensure that BootP and IP are enabled 
on the incoming and outgoing interfaces.

4.

Ensure that the link modules and drivers are enabled.

For instructions, see 

Configuring and Managing Routers with Site Manager

.

BootP Server Not Sending BootP Responses

If the BootP server is receiving BootP requests but is failing to respond to them, 
do the following:

1.

Follow the instructions in “Displaying the BootP Server IP Routes” on 

page B-15

.

2.

Follow the instructions in “Debugging the BootP Server” on 

page B-12

.

3.

Ensure that the 

/etc/inetd.conf

 

file contains no more than one 

bootps

 

entry. 

If there is more than one entry, comment out the invalid entry. The valid entry 
is as follows:

bootps dgram udp wait root /etc/bootpd bootpd

4.

Ensure that the 

tftp dgram

 entry in the 

/etc/inetd.conf

 

file is correct for 

your system. 

For instructions, see “Setting Up a TFTP Server” on page 2-9.

5.

See “Verifying the BootP Server Setup” on 

page B-14

.

Summary of Contents for AN Series















































































































































Reviews:

No comments