manualshive.com logo in svg

Nortel AN Series, Configuration Manual, Page: 105 / 142

Share
Download
Nortel AN Series Configuration Manual Download Page 105

Troubleshooting Network Boot Problems

308614-14.20 Rev 00

B-7

 

Use the 

set 

command to correct settings, if necessary. For example, if the 

router has a token ring port and the 

wfDrivers.wfTMS380Load.0

 

setting 

is not 

2147483648

, enter the following command to correct it:

set   wfDrivers.wfTMS380Load.0   2147483648;commit

•

If the router is netbooting with a synchronous interface, enter the 
following command to display information about the interface, where 

connector

 is the interface connector number:

get   wfSyncEntry.*.1.

<connector>

Ensure that external clocking is set.

•

If the router is netbooting with an Ethernet interface, enter the following 
command to display information about the interface, where 

connector

 is 

the interface connector number:

get   wfCSMACDEntry.*.1.

<connector>

•

If the router is netbooting with a token ring interface, enter the following 
command to display information about the interface, where 

connector

 is 

the interface connector number:

get   wfTokenRingEntry.*.1.

<connector>

Summary of Contents for AN Series















































































































































Reviews:

No comments