Nortec NHRS 010-090 Installation And Operation Manual Download

Page: 61 / 70

Troubleshooting | 58

NHRS Electric Steam Humidifier – Mandatory Pre-Start-Up Checklist (p2 of 3)

DRAIN LINES:

Air gap located within 3ft of the unit





Slopped to drain





Size:______________

WIRING:

No loose wires around the unit or on the PC board? Yes









CONTROLS:

Installed

Location/Wiring/Setting

High limit:







_________________



Air proving:

 







_________________



Mod controller:





_________________

Other:







_________________

POWER:

Voltage, amperage rating and fuse corresponds to Spec Label





Disconnect switch located close to humidifier



Field contact:___________________________ Signature:_______________________________

Summary of Contents for NHRS 010-090







































































Search results

Summary of Contents for NHRS 010-090

Reviews:

Related manuals for NHRS 010-090

Brands by name

Popular brands

Nortec NHRS 010-090, Installation And Operation Manual

Search results

Summary of Contents for NHRS 010-090

Reviews:

Related manuals for NHRS 010-090

Brands by name

Popular brands