Nortec NHRS 010-090 Installation And Operation Manual Download | Manualshive

Page: 17 / 70

background image

Installation | 14

Steam Distributor



Steam generated by the NHRS may be distributed directly into a conditioned
environment with a Remote Blower Pack (P/N 2572615), or into an air handling system
using either Nortec steam distributors or Nortec’s SAM-e steam distribution manifold.



The steam distributor should be installed as close as possible to the humidifier. Short
steam distribution lines minimize condensate losses and the possibility of generating
back pressure in the steam distribution line.



Figure 8 provides common guidelines for locating a steam distributor in a duct.

Figure 8: Distributor Location in Duct

Note:

• Install the NHRS as close as possible to whatever steam distributor is used.
• Refer to distributor, SAM-e, or Remote Blower Pack installation manuals for detailed

installation instructions (2556592, 1507619, and 2572641, respectively)

«
...
15
16
17
18
19
...
»

Summary of Contents for NHRS 010-090







































































Reviews:

No comments

Related manuals for NHRS 010-090

Brand: East Pages: 15

O Breeze FM102BL

Brand: Canary Products Pages: 4

Brand: DriSteem Pages: 18

Micro-stat H200 Series

Brand: Viconics Pages: 6

Indurre IND-600

Brand: KAF International Pages: 7

Brand: Master Pages: 75

Brand: Aircare Pages: 13

Brand: Aircare Pages: 24

Brand: Aircel Pages: 52

Brand: Air-O-Swiss Pages: 13

Brand: Air-O-Swiss Pages: 128

Brand: Danby Pages: 28

Brand: Danby Pages: 32

Brand: Danby Pages: 32

Brand: Danby Pages: 40

Brand: EMAG Pages: 2

Brand: Hikari Pages: 17

Brand: WC Wood Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands