Nortec NHRS 010-090 Installation And Operation Manual Download Page 14 | Manualshive

Page: 14 / 70

background image

11 | Installation

Blower Pack Clearance Requirements

For more information regarding the clearance requirements of the Remote Mounted Blower
Pack (P/N 2572615), refer to installation manual (document number 2572641).

Table 4: Clearances for Blower Packs on Low Speed*

Humidifier

Capacity

lb/hr (kg/hr)

Min. Frontal

Clearance

Inches (cm)

Min. Overhead

Clearance

Inches (cm)

Min. Left Side

Clearance

Inches (cm)

Min. Right Side

Clearance

Inches (cm)

Up to 30 (13.6)

132 (336)

12 (31)

12 (31)

12 (31)

30-100

(13.6-45.4)

Not

recommended

Not

recommended

Not

recommended

Not

recommended

Table 5: Clearances for Blower Packs on High Speed*

Humidifier

Capacity

lb/hr (kg/hr)

Min. Frontal

Clearance

Inches (cm)

Min. Overhead

Clearance

Inches (cm)

Min. Left Side

Clearance

Inches (cm)

Min. Right Side

Clearance

Inches (cm)

Up to 30 (13.6)

132 (336)

12 (31)

12 (31)

12 (31)

30-100

(13.6-45.4)

Not

recommended

Not

recommended

Not

recommended

Not

recommended

*NOTES:
Nominal Conditions: 72ºF (22.2ºC), 43% RH.
Low speed not recommended for 50-100 lb/hr humidifiers.
Blower Pack should not be installed near cold surfaces or where dew point may be reached.
Higher humidity or lower room temperature may result in longer absorption distances.

«
...
12
13
14
15
16
...
»

Summary of Contents for NHRS 010-090







































































Reviews:

No comments

Related manuals for NHRS 010-090

Brand: Calorex Pages: 15

Brand: Calorex Pages: 20

Brand: Soleus Air Pages: 8

Brand: Pur Line Pages: 22

Brand: Clarke Pages: 16

Brand: Champion Pages: 16

aroma humidifier

Brand: Impulsion Pages: 16

Brand: Nemaxx Pages: 86

Brand: DrBrowns Pages: 5

Brand: Amcor Pages: 4

Brand: Crane Pages: 12

Brand: Goldair Pages: 8

Brand: Beurer Pages: 84

Brand: BMT Pages: 9

Brand: NANO Pages: 32

Brand: Elsteam Pages: 12

Brand: Skuttle Pages: 12

Brand: HAEGER Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands