Nortec NHRS 010-090 Installation And Operation Manual Download Page 34 | Manualshive

Page: 34 / 70

background image

31 | Installation

Options and Accessories

Blower Pack

Optional blower pack (part number 2572615) can be used to distribute steam to localized
areas, or in areas that do not have built-in air distribution systems. Blower packs are available
in remote configuration, are piped in the field, and are wired to the humidifier RMBP power
source (or a separate power source if the installation requires).

For detailed installation information, refer to the Blower Pack installation and operation manual
(document 2572641). Refer to Table 4 and Table 5 on Page 11 for clearance information.

Note:
For installation of options and accessories follow the instructions that are provided with them.

Figure 26: Remote Mounted Blower Pack.

«
...
32
33
34
35
36
...
»

Summary of Contents for NHRS 010-090







































































Reviews:

No comments

Related manuals for NHRS 010-090

Brand: Anden Pages: 12

Brand: Paris Rhone Pages: 11

Brand: Walton Pages: 6

Brand: eta Pages: 32

Brand: Clean Air Pages: 11

Brand: Kroll Pages: 12

Brand: Air Naturel Pages: 7

Brand: Air Naturel Pages: 40

Brand: ALPATEC Pages: 20

Brand: Duronic Pages: 97

Brand: Ecoair Pages: 15

Brand: Ecoair Pages: 17

Brand: Magnavox Pages: 6

Brand: Vapac Pages: 10

PLATINUM DrySmart GPDH440

Brand: Goldair Pages: 24

Brand: Vemer Pages: 2

Brand: Lacme Pages: 27

Brand: WC Wood Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands