Newland NLS-BS30 User Manual Download Page 21

Page: 21 / 247

** Exit Setup

Enter Setup

Use of Programming Command

Besides the barcode programming method, the scanner can also be configured by serial commands (HEX) sent from the

host device.

All commands must be entered in uppercase letters

Use of Programming Barcodes

Scanning the

Enter Setup

barcode can enable the scanner to enter the setup mode. Then you can scan a number of

programming barcodes to configure your scanner. To exit the setup mode, scan the

Exit Setup

barcode or a non-

programing barcode, or reboot the scanner.

** Exit Setup

Enter Setup

Programming barcode data (i.e. the characters under programming barcode) can be transmitted to the host device. You

may scan the appropriate barcode below to enable or disable the transmission of programming barcode data to the host

device.

** Do Not Transmit Programming Barcode Data

Transmit Programming Barcode Data

Summary of Contents for NLS-BS30
























































































































































































































































Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands

Newland NLS-BS30, User Manual

Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands