Newland NLS-BS30 User Manual Download Page 202

Page: 202 / 247

Enter Setup

** Exit Setup

188

Change Data Format for a Single Scan

You can switch between data formats for a single scan. The next barcode is scanned using the data format selected here,

then reverts to the format you have selected above.

For example, you may have set your scanner to use the data format you saved as Format_3. You can switch to Format_1

for a single trigger pull by scanning the

Single Scan

– Format_1

barcode below. The next barcode that is scanned uses

Format_1, then reverts back to Format_3.

Note: This setting will be lost by removing power from the scanner, or turning off/ rebooting the device.

Single Scan

– Format_0

Single Scan

– Format_1

Single Scan

– Format_2

Single Scan

– Format_3

Summary of Contents for NLS-BS30
























































































































































































































































Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands

Newland NLS-BS30, User Manual

Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands