Newland NLS-BS30 User Manual Download Page 15

Page: 15 / 247

Preface

Introduction

This manual provides detailed instructions for setting up and using the BS30 wireless barcode scanner (hereinafter

referred to as “

the scanner

”).

Chapter Description

Chapter 1 Getting Started

Gives a general description of BS30 scanner.

Chapter 2 EasySet

Introduces a useful tool you can use to set up BS30 canner and develop

new applications.

Chapter 3 System Settings

Introduces three configuration methods and describes how to configure

general parameters of BS30 scanner.

Chapter 4 USB Interface

Describes how to configure USB communication parameters.

Chapter 5 Wireless Communication

Describes how to configure the parameters necessary for wireless

communication between the scanner nd host device.

Chapter 6 Symbologies

Lists all compatible symbologies and describes how to configure the

relevant parameters.

Chapter 7 Data Formatter

Explains how to customize scanned data with the data formatter.

Chapter 8 Prefix & Suffix

Describes how to use prefix and suffix to customize scanned data.

Chapter 9 Batch Programming

Explains how to integrate a complex programming task into a single

barcode.

Appendix

Provides factory defaults table and a bunch of frequently used

programming barcodes.

Summary of Contents for NLS-BS30
























































































































































































































































Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands

Newland NLS-BS30, User Manual

Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands