Newland NLS-BS30 User Manual Download Page 48

Page: 48 / 247

Enter Setup

** Exit Setup

Power Off/Battery Off

Power Off Scanner

Battery Off

(For Long-term Storage/Shipping)

Note: After scanning the

Battery Off

barcode, you MUST press the trigger for 6~7 seconds or connect the host via USB

to turn it on. The scanner will beep when it is powered on.

Default Settings

Factory Defaults

Scanning the following barcode can restore the scanner to the factory defaults.

You may need to reset all parameters to the factory defaults when:

The scanner is not properly configured so that it fails to decode barcodes.

You forget previous configuration and want to avoid its impact.

**Restore All Factory Defaults

Custom Defaults

Scanning the

Restore All Custom Defaults

barcode can reset all parameters to the custom defaults. Scanning the

Save

as Custom Defaults

barcode can set the current settings as custom defaults.

Custom defaults are stored in the non-volatile memory.

Summary of Contents for NLS-BS30
























































































































































































































































Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands

Newland NLS-BS30, User Manual

Search results

Summary of Contents for NLS-BS30

Reviews:

Related manuals for NLS-BS30

Brands by name

Popular brands