NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 162 / 162

Table 4. Router specifications (Continued)

Description

Feature

Compatible with 10BASE-T, 100BASE-TX, 1000BASE-T, or RJ-45

WAN

Maximum WiFi signal rate complies with the IEEE

802.11 standard.

• 2.4GHz AX: 2x2 (Tx/Rx) 1024/256-QAM 20/40MHz, up to 600 Mbps

• 5GHz AX: 4x4 (Tx/Rx) 1024-QAM 20/40/80/160MHz, up to 4800 Gbps

• Backwards compatible with 802.11a/b/g/n/ac WiFi

WiFi

Auto Rate Sensing

Radio data rates

IEEE 802.11ax 2.4GHz 1024 QAM support
IEEE 802.11ax 5.0GHz 80 MHz 1024 QAM support

Data encoding standards

Limited by the amount of WiFi network traffic generated by each node (typically
50–70 nodes).

Maximum computers per
wireless network

WPA2-PSK and WPA/WPA2

802.11 security

Maximum wireless signal rate derived from IEEE 802.11 specifications. Actual data throughput and wireless coverage

will vary and may be lowered by network and environmental conditions, including network traffic volume and building

construction. NETGEAR makes no representations or warranties about this product’s compatibility with AX standards.

User Manual

162

Supplemental Information

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands