NETGEAR Nighthawk AX6 AX4300 User Manual Download | Manualshive

Page: 38 / 162

background image

With a 6rd tunnel configuration, the router follows the RFC5969 standard, supporting
two ways to establish a 6rd tunnel IPv6 WAN connection:

•

Auto Detect mode. In IPv6 Auto Detect mode, when the router receives option 212
from the DHCPv4 option, autodetect selects the IPv6 as 6rd tunnel setting. The router
uses the 6rd option information to establish the 6rd connection.

•

Manual mode. Select 6rd Tunnel. If the router receives option 212, the fields are
automatically completed. Otherwise, you must enter the 6rd settings.

To set up an IPv6 6rd Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select 6rd.

The page adjusts.

The router automatically detects the information in the following sections:

• 6rd (IPv6 Rapid Development) Configuration. The router detects the service

provider’s IPv4 network and attempts to establish an IPv6 6rd tunnel connection.
If the IPv4 network returns 6rd parameters to the router, the page adjusts to display
the correct settings in this section.

• Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired

for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.

6. Select an IPv6 Domain Name Server (DNS) Address radio button:

• Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.

Your ISP automatically assigns this address.

• Use These DNS Servers. If you know that your ISP requires specific servers, select

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.

User Manual

38

Specify Your Internet Settings

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
36
37
38
39
40
...
»

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Reviews:

No comments

Related manuals for Nighthawk AX6 AX4300

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Brand: C&H Technologies Pages: 46

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

Brand: H3C Pages: 45

Brand: H3C Pages: 80

Brand: H3C Pages: 46

Brand: H3C Pages: 45

Brand: H3C Pages: 4

Brand: H3C Pages: 184

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands