NETGEAR Nighthawk AX6 AX4300 User Manual Download | Manualshive

Page: 115 / 162

background image

6. Right-click the USB device and select Map network drive.

The Map Network Drive window opens.

7. Select the drive letter to map to the new network folder.

8. Click the Finish button.

The USB storage device is mapped to the drive letter that you specified.

9. To connect to the USB storage device as a different user, select the Connect using

different credentials check box, click the Finish button, and do the following:

a. Type the user name and password.

b. Click the OK button.

Access a storage device that is connected
to the router from a Mac

From a computer or device on the network, you can access a storage device that is
connected to the router.

To access the device from a Mac:

1. Connect a USB storage device to a USB port on your router.

2. If your USB storage device uses a power supply, connect it.

You must use the power supply when you connect the USB storage device to the
router.

When you connect the USB storage device to the router’s port, it might take up to
two minutes before it is ready for sharing. By default, the USB storage device is
available to all computers on your local area network (LAN).

3. On a Mac that is connected to the network, select Go > Connect to Server.

The Connect to Server window opens.

4. In the Server Address field, enter smb://readyshare.

5. When prompted, select the Guest radio button.

If you set up access control on the router and you allowed your Mac to access the
network, select the Registered User radio button and enter admin for the name
and router admin password for the password. For more information about access
control, see Enable access control to allow or block access to the Internet on page
43.

User Manual

115

Share USB Storage Devices
Attached to the Router

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
113
114
115
116
117
...
»

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Reviews:

No comments

Related manuals for Nighthawk AX6 AX4300

Wireless Router

Brand: Watchguard Pages: 11

Brand: D-Link Pages: 32

Brand: D-Link Pages: 28

Brand: D-Link Pages: 48

Brand: D-Link Pages: 83

Brand: D-Link Pages: 155

Brand: TDC Pages: 27

Brand: Niveo Pages: 155

Brand: Premio Pages: 3

ADSL 2/2+ Router with USB Port ADE-3410v2

Brand: Planet Pages: 62

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: Vaisala Pages: 32

Brand: SyChip Pages: 24

Ultrastar Serv24 S2122-N24-4

Brand: HGST Pages: 36

Brand: Tenda Pages: 120

JetStream T2600G-28TS

Brand: TP-Link Pages: 1136

Air Live GW-300R

Brand: Ovislink Pages: 20

EZ Switch SMC-EZ1024FDT

Brand: SMC Networks Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands