NETGEAR Nighthawk AX6 AX4300 User Manual Download | Manualshive

Page: 40 / 162

background image

For example, if a secure website does not open, or displays only part of a web page,
you might need to change the MTU.

•

You use VPN and experience severe performance problems.

•

You used a program to optimize MTU for performance reasons and now you are
experiencing connectivity or performance problems.

CAUTION:

An incorrect MTU setting can cause Internet communication problems. For

example, you might not be able to access certain websites, frames within websites,
secure login pages, or FTP or POP servers.

If you suspect an MTU problem, a common solution is to change the MTU to 1400. If
you are willing to experiment, you can gradually reduce the MTU from the maximum
value of 1500 until the problem goes away. The following table describes common MTU
sizes and applications.

Table 2. Common MTU sizes

Application

MTU

The largest Ethernet packet size. This setting is typical for
connections that do not use PPPoE or VPN and is the default value
for NETGEAR routers, adapters, and switches.

1500

Used in PPPoE environments.

1492

Maximum size to use for pinging. (Larger packets are fragmented.)

1472

Used in some DHCP environments.

1468

Used in PPPoA environments.

1458

Used in PPTP environments or with VPN.

1436

Change the MTU size

To change the MTU size:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

User Manual

40

Specify Your Internet Settings

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
38
39
40
41
42
...
»

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Reviews:

No comments

Related manuals for Nighthawk AX6 AX4300

Brand: ZyXEL Communications Pages: 2

Brand: Juniper Pages: 825

Brand: AMX Pages: 2

Brand: Comelit Pages: 19

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

SmartSTACK ELS100-24TXM

Brand: Cabletron Systems Pages: 117

Brand: Top Pages: 21

Brand: Buffalo Pages: 2

Brand: Hamlet Pages: 11

WebShare 141 WN

Brand: Atlantis Pages: 78

Brand: Telestar Pages: 16

IE-SW-VL09T-6TX-3SC

Brand: Weidmuller Pages: 14

Brand: Lanner Pages: 141

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

SecPath F50X0 Series

Brand: H3C Pages: 41

Brand: ACTi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands