NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 131 / 162

14. To specify the destination folder, click the Browse button and select a destination

folder.

15. Click the Install button.

The window displays the progress of the installation and then displays the final
installation page.

16. Click the Finish button.

17. Unzip the configuration files that you downloaded and copy them to the folder where

the VPN client is installed on your device.
For a client device with Windows 64-bit system, the VPN client is installed at

C:\Program files\OpenVPN\config\

by default.

18. For a client device with Windows, modify the VPN interface name to NETGEAR-VPN:

a. On your computer, go to the Networks page. If you are using Windows 10, select

Control Panel > Network and Sharing Center > Change adapter settings.

b. In the local area connection list, find the local area connection with the device

name TAP-Windows Adapter.

User Manual

131

Use VPN to Access Your Network

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands