NETGEAR Nighthawk AX6 AX4300 User Manual Download | Manualshive

Page: 70 / 162

background image

•

WPA2-PSK [AES]. WPA2 provides a secure and fast connection but some older
WiFi devices do not detect WPA2 and support only WPA. Select WPA2-PSK [AES]
security to allow 802.11n devices to connect to the 2.4 GHz or 5 GHz guest WiFi
network at the fastest speed. If your network includes older devices that do not
support WPA2, select WPA-PSK [TKIP] + WPA2-PSK [AES] security. To use WPA2
security, in the Password (Network Key) field, enter a phrase of 8 to 63
characters. To join the 2.4 GHz or 5 GHz guest WiFi network, a user must enter
this password.

•

WPA-PSK [TKIP] + WPA2-PSK [AES]. This type of security enables WiFi devices
that support either WPA or WPA2 to join the 2.4 GHz band of the guest WiFi
network. However, WPA-PSK [TKIP] is less secure than WPA2-PSK [AES] and limits
the speed of WiFi devices to 54 Mbps. To use WPA + WPA2 security, in the
Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the
2.4 GHz or 5 GHz guest WiFi network, a user must enter this password.

7. Click the Apply button.

Your settings are saved.

8. Make sure that you can reconnect over WiFi to the network with its new security

settings.
If you cannot connect over WiFi, check the following:

•

If your computer or mobile device is already connected to another WiFi network
in your area, disconnect it from that WiFi network and connect it to the WiFi
network that the router provides.
Some WiFi devices automatically connect to the first open network without WiFi
security that they discover.

•

Does your computer or mobile device display as an attached device?
If it does, it is connected to the network.

•

Are you using the correct network name (SSID) and password?

Enable or disable the WiFi radios

If you used the WiFi On/Off button to turn off the WiFi radios, you can’t log in to the
router to turn them back on. You must press the WiFi On/Off button again for two
seconds to turn the WiFi radios back on.

User Manual

70

Manage Network Settings

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
68
69
70
71
72
...
»

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Reviews:

No comments

Related manuals for Nighthawk AX6 AX4300

Brand: IBM Pages: 72

Univerge SV8100

Brand: NEC Pages: 44

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Network Card-MS

Brand: Eaton Pages: 89

Brand: Conceptronic Pages: 230

WGR614 - Wireless-G Router Wireless

Brand: NETGEAR Pages: 116

Brand: Aewin Technologies Pages: 86

SmartSTACK ELS100-24TXM

Brand: Cabletron Systems Pages: 117

Brand: ACTi Pages: 14

Brand: TP-Link Pages: 4

Brand: CopperOptics Pages: 12

Mobileraid MR8X

Brand: Sans Digital Pages: 81

Brand: LevelOne Pages: 146

Brand: Hama Pages: 7

Brand: ZyXEL Communications Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands