NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 13 / 162

Router label

The router label shows the login information, WiFi network name (SSID), password,
serial number, and MAC address.

Figure 4. Router label

Attach and position the antennas

Before you install your router, attach the antennas to the router.

Note: Make sure to match the labels on the antennas with the labels on the router. The
antennas must be attached to the correct antenna post on the router.

After you are done attaching the antennas, position the antennas as shown.

Figure 5. Attach and position the antennas

User Manual

Hardware Setup

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands