NETGEAR Nighthawk AX6 AX4300 User Manual Download | Manualshive

Page: 104 / 162

background image

To erase the settings:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Administration > Backup Settings.

The Backup Settings page displays.

5. Click the Erase button.

The configuration is reset to factory default settings. When the reset is complete,
the router restarts. This process takes about two minutes.

WARNING:

To avoid the risk of corrupting the firmware, do not interrupt the reset.

For example, do not close the browser, click a link, or load a new page. Do not turn
off the router. Wait until the router finishes restarting.

Restore the settings

To restore configuration settings that you backed up:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Administration > Backup Settings.

The Backup Settings page displays.

5. Click the Browse button to find and select the

.cfg

file.

6. Click the Restore button.

User Manual

104

Manage Your Router

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
102
103
104
105
106
...
»

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Reviews:

No comments

Related manuals for Nighthawk AX6 AX4300

Brand: B+B SmartWorx Pages: 4

Brand: D-Link Pages: 213

Brand: Macsense Pages: 39

Brand: NETGEAR Pages: 84

Brand: Rosewill Pages: 3

Brand: Network Critical Pages: 200

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

IE-SW-PL09M-5GC-4GT

Brand: Weidmuller Pages: 15

EdgePoint EP-R8

Brand: Ubiquiti Pages: 22

Brand: Commax Pages: 122

Brand: Paradyne Pages: 6

Brand: National Instruments Pages: 37

Brand: Ryobi Pages: 84

Brand: GE Pages: 24

0150-0241 ProBridge

Brand: GE Pages: 19

Brand: GE Pages: 39

Brand: GE Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands