NEC V850E/MA1 Application Note Download Page 40

Page: 40 / 99

CHAPTER 3 SPECIFICATIONS OF PCI HOST BRIDGE MACRO

Application Note U17121EJ1V1AN

3.4.7 PCI_ERR_ADD register

The PCI_ERR_ADD register retains the PCI bus address when the following errors occur.

•

System error (SERR# reception)

•

Parity error (PERR# reception)

•

Master

abort

•

Target

abort

When the PCI_ERR_ADD register is read, all the bits are cleared. Once an error occurs and a value is set to the

PCI_ERR_ADD register, the first value is retained until read access is performed or a new error occurs and the value

is updated.

This function is used only for debugging and is not used in normal operation.

After reset: 00000000H R Offset address: 1CH

ERR_ADR

Bit Name

R/W

Function

ERR_ADR

Retains the address when a PCI bus error occurs.

Summary of Contents for V850E/MA1




































































































Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands

NEC V850E/MA1, Application Note

Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands