NEC V850E/MA1 Application Note Download Page 30

Page: 30 / 99

CHAPTER 2 OVERVIEW OF PCI HOST BRIDGE MACRO

Application Note U17121EJ1V1AN

2.2 Features

The features of the PCI host bridge macro are as follows.

•

PCI bus master cycle control

PCI configuration register read/write single cycle

PCI I/O register read/write single cycle

PCI memory read/write single cycle

•

PCI bus slave cycle control

PCI memory read/write cycle (burst transfer up to 8 doublewords (32 bits

8 bursts))

•

PCI bus arbiter control

Up to 8 masters can be controlled (one of them is occupied by the PCI host bridge macro)

Bus parking master: Limited to PCI host bridge macro/selectable from the last accessed master

•

PCI bus error processing

An error interrupt is generated for master abort/target abort/PERR# reception/SERR# reception

The address immediately before an error occurs is retained

•

PCI bus address conversion control

PCI I/O address and PCI memory address registers are supported to convert the physical addresses from

the CPU to addresses for the PCI bus

•

CPU interface control

External bus interface (MEMC)

Data bus width: 32 bits/16 bits

Cycle control by hardware wait control

•

SDRAM

control

SDRAM is controlled in response to main memory (SDRAM) access from the PCI device

Data bus width: 16 bits/32 bits are supported

•

PCI

clock

33 MHz supported

SDRAM control and PCI control clocks are designed to be asynchronous

Summary of Contents for V850E/MA1




































































































Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands

NEC V850E/MA1, Application Note

Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands