manualshive.com logo in svg

NEC PD789488, User Manual

The NEC PD789488 User Manual is a comprehensive guide that enables users to fully understand and utilize the features of the PD789488 model. This manual offers step-by-step instructions and troubleshooting tips. Download it for free from manualshive.com to unlock the full potential of your NEC PD789488 device.

Share
Download
background image

CHAPTER  12   SERIAL  INTERFACE  1A0 

 

238 

User’s Manual  U15331EJ4V1UD

 

In 6-byte transmission/reception (bit 6 (ARLD0) and bit 7 (RE0) of automatic data transmit/receive control 
register 0 (ADTC0) = 0, and 1, respectively) in basic transmit/receive mode, buffer RAM operates as follows. 

 

(i)  Before transmission/reception (refer to Figure 12-9 (a)) 

After any data has been written to SIO1A0 (start trigger:  this data is not transferred), transmit data 1 
(T1) is transferred from the buffer RAM to SIO1A0.  When transmission of the first byte is completed, 
receive data 1 (R1) is transferred from SIO1A0 to the buffer RAM, and automatic data 
transmit/receive address pointer 0 (ADTP0) is decremented.  Then transmit data 2 (T2) is 
transferred from the buffer RAM to SIO1A0. 
 

(ii)  4th byte transmit/receive point (refer to Figure 12-9 (b)) 

Transmission/reception of the third byte is completed, and transmit data 4 (T4) is transferred from 
the buffer RAM to SIO1A0.  When transmission of the fourth byte is completed, receive data 4 (R4) 
is transferred from SIO1A0 to the buffer RAM, and ADTP0 is decremented. 
 

(iii) Completion of transmission/reception (refer to Figure 12-9 (c)) 

When transmission of the sixth byte is completed, receive data 6 (R6) is transferred from SIO1A0 to 
the buffer RAM, and the interrupt request flag (CSIIF10) is set (INTCSI10 generation). 
 

          Figure 12-9.  Buffer RAM Operation in 6-Byte Transmission/Reception  
                                (in Basic Transmit/Receive Mode) (1/2) 

(a) Before transmission/reception 

 

 

 

Transmit data 1 (T1)

Transmit data 2 (T2)

Transmit data 3 (T3)

Transmit data 4 (T4)

Transmit data 5 (T5)

Transmit data 6 (T6)

FFAFH

FFA5H

FFA0H

Receive data 1 (R1)

SIO1A0

0

CSIIF10

5

ADTP0

_1

Summary of Contents for PD789488





































































































































































































































































































































































































Reviews:

No comments

Related manuals for PD789488

ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
Queclink GV600 Series Instruction Manual preview
GV600 Series
Brand: Queclink Pages: 9
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
Supero Supero SAS-826A User Manual preview
Supero SAS-826A
Brand: Supero Pages: 16
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Brand: NEC Pages: 6
ZALMAN Fatal1ty FS-V7 User Manual preview
Fatal1ty FS-V7
Brand: ZALMAN Pages: 9
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Brand: ZALMAN Pages: 16
Idis DR-8516 Installation Manual preview
DR-8516
Brand: Idis Pages: 28
SMC Sierra Monitor FPC-N38 Startup Manual preview
FPC-N38
Brand: SMC Sierra Monitor Pages: 43
KTI Networks KGS-2421 Installation Manual preview
KGS-2421
Brand: KTI Networks Pages: 25
Magma ExpressBox4 1U Quick Installation Manual preview
ExpressBox4 1U
Brand: Magma Pages: 2
Pro-Log STD 7000 User Manual preview
STD 7000
Brand: Pro-Log Pages: 59
X-Micro XWL-11GPIG Quick Start Manual preview
XWL-11GPIG
Brand: X-Micro Pages: 9
X-Micro XWL-11BPRG User Manual preview
XWL-11BPRG
Brand: X-Micro Pages: 17
X-Micro XWL-11GPRG User Manual preview
XWL-11GPRG
Brand: X-Micro Pages: 31
Sun Microsystems Sun Enterprise 10000 Installation Manual preview
Sun Enterprise 10000
Brand: Sun Microsystems Pages: 42

Brands by name

Popular brands

Load more brands