NEC Express5800/140Hf User Manual Download Page 422

Page: 422 / 482

9-60 Upgrading Your Server

Make sure that the memory board power lamp goes off, then remove the memory board.

IMPORTANT:

The memory board becomes very hot while being

powered. When removing the board, turn off the power and wait for
several minutes before pulling it out.

Note that the hot-plug memory board is off-powered when it is
unlocked (the LED goes off). Wait several minutes in this state.

Hold the ejector and pull the memory board out from the server.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Search results

Summary of Contents for Express5800/140Hf

Reviews:

Brands by name

Popular brands

NEC Express5800/140Hf, User Manual

Search results

Summary of Contents for Express5800/140Hf

Reviews:

Brands by name

Popular brands