manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 199

Configuring Your Server    4-111

1

Choose whether or not to acquire the IP address of the DNS server automatically by
DHCP.

2

If DHCP is not used to automatically acquire the IP address of the DNS server, make
settings here. If DHCP is used, information automatically acquired appears here.

1

The default host name to be used when no host name is configured for using DHCP

2

Enter the host name of BMC. If nothing is set here, the default host name in the previous step
will be used.

3

Enter the domain name of the network to which BMC belongs.

4

Choose whether or not to register the host name to the DNS server.

1

2

1

2

3

4

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands