manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 306

8-12  Troubleshooting

Fan Error Lamp

The fan error lamp lights amber when an error occurs on the fan. Check the Fan Fault lamp being lit
red to identify the failed fan (see "FAN Fault Lamps" described later).

Thermal Error Lamp

The thermal error lamp lights amber when an abnormal temperature in the server is detected. Check
the room temperature where the server is installed.

Access Lamps

The access lamps for the DVD-ROM drive light when access is made to a media in the drive.

Fan error lamp

Thermal error lamp

ACCESS lamp

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands