manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 289

Maintenance  7-7

SYSTEM DIAGNOSTICS

The System Diagnostics runs several tests on the server.

Select [Tools] - [System Diagnostics] in the NEC EXPRESSBUILDER to diagnose the system.

Test Items

The following items are tested in system diagnostics.

„

 

Memory

„

 

CPU cache memory

„

 

Hard disk drive used as a system

IMPORTANT:

 When executing the system diagnostics, make sure to

disconnect the LAN cable. Executing the system diagnostics with the
LAN cable connected, the network may be influenced.

NOTE:

 On checking the hard disk drive, no data is written into the

disk.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands