manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 147

Configuring Your Server    4-59

Configuration Wizard

Use this wizard to configure a RAID using the HDDs. The detailed explanation of this feature is
given in "Configuring Virtual Disk".

Adapter Selection

If several disk array controllers N8103-90 are installed in the server, you need to select an adapter
controlled by WebBIOS to configure each adapter. Clicking [Adapter Selection] on WebBIOS top
menu opens the [Adapter Selection] screen again.

Physical View / Logical View

If the virtual disk has been configured using the disk array controller, DG (disk group) is displayed
on WebBIOS top menu. Clicking [Physical View] displays information for HDDs in DG. Clicking
[Logical View] displays virtual disk in DG.

Events

The Events screen is used to confirm the system events.

IMPORTANT:

 The On Board RAID (MegaRAID ROMB) does not

support Events feature.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands