manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 210

4-122  Configuring Your Server

Loading Update Data Files

When you click [

] to add update files, a window as shown below opens prompting you to select

files.

Select update data files.

When you click [Open] after specifying files, loading of the files begins.

It will take a little while for loading to be completed.

NOTE:

 Because update can be made globally for each update target,

make sure to load everything you need.
You can specify multiple files to be loaded simultaneously.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands