manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 119

Configuring Your Server    4-31

Boot

Positioning the cursor on "Boot" shows the Boot menu which is used to set the boot priority.

The server searches for devices in the order set in this menu on booting.    Finding the boot software,
the server starts the software.

The priority of the boot devices can be changed by using the 

↑

, 

↓

, 

+

, and 

-

 keys.    Move the cursor

to the desired device with the 

↑

 or 

↓

 key and change the priority with the 

+

 or 

-

 key.

IMPORTANT:

 To boot NEC EXPRESSBUILDER, set the priority of

the devices as shown in the figure above.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands