NEC Express5800/140Hf User Manual Download | Manualshive

Page: 232 / 482

background image

5-12 Installing the Operating System with Express Setup

11.

Next, [Basic Information] wizard appears. Confirm the parameters, modify if necessary,
and then click [Next].

After that, click [Next], [Back], or [Help] on the screen to continue. Modify the
parameters each time if necessary.

IMPORTANT:

Reserve the partition to install the OS more than the minimally
required size.

If you select "Use Existing Partition" at "System Partition", the
information included in the first partition (excluding maintenance
partition) will all be formatted and deleted. The information
included in the other partition will be retained. In the figure
below, describes the partition which information will be deleted
when maintenance partition exists.

First Partition

<Maintenance Partition>

Retained

Second

Partition

Deleted

Third

Partition

Retained

Fourth

Partition

Retained

You can not re-install the system with the existing partition that is
upgraded to Dynamic Disk remained. Do not select "Use Existing
Partition" at "System Partition".

If you specify other than 4095MB for the "Partition Size", it is
necessary to convert to NTFS.

If "Use Existing Partition" at "System Partition" is selected but the
partition other than the one to install Windows Server 2003 does
not exist (excluding maintenance partition), Express Setup will
reserve the maximum area of the hard disk to install Windows
Server 2003.

You can not go to the next screen if the specification is incorrect.

On specification, an error may occur in relationship with the
specified contents of the former screen and require to go back to
modify the specification.

During the setup, the screen to specify the partition that Windows
Server 2003 is to be installed appears. The first 55MB area
displayed on the screen is a partition that is used to store the
configuration information or utilities unique of the server. We do
not recommend to delete this area, but if you do not want to
reserve this 55MB area, perform the installation by manual setup.
It is unable to delete this area by Express Setup.

«
...
230
231
232
233
234
...
»

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/140Hf

eServer 380 xSeries

Brand: IBM Pages: 112

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

Brand: ACTi Pages: 11

Brand: Nortel Pages: 144

Brand: Protogate Pages: 30

Brand: Cavalry Pages: 16

Brand: Fujitsu Pages: 26

Brand: Fujitsu Pages: 56

Brand: Fujitsu Pages: 36

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 30

ETERNUS DX Disk

Brand: Fujitsu Pages: 85

Brand: Fujitsu Pages: 111

BX630 - PRIMERGY - S2 Dual

Brand: Fujitsu Pages: 64

Brand: Fujitsu Pages: 68

CELVIN NAS QE707

Brand: Fujitsu Pages: 95

BX630 - PRIMERGY - S2 Dual

Brand: Fujitsu Pages: 90

D3320 PRIMERGY BX2560 M2

Brand: Fujitsu Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands