manualshive.com logo in svg

NEC Express5800/140Hf, User Manual

Share
Download
NEC Express5800/140Hf User Manual Download Page 115

Configuring Your Server    4-27

The table below shows the operation when the AC power to the server is turn off once and then on
again, depending on the setting of "AC-LINK."

Setting of AC-LINK

System status before AC power off

Stay Off

Last State

Power On

Operating

Off

On

On

Aborting (DC power being off also)

Off

Off

On

Forced shutdown

Off

Off

On

* Press the power switch continuously at least four seconds.    This forcibly turns off the power.

IMPORTANT:

 Set this item to "Power on" in order to link the AC

power source supplied from UPS when the server is connected to UPS.

Summary of Contents for Express5800/140Hf



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands