manualshive.com logo in svg

NEC Express5800/110Ge, User Manual, Page: 288 / 332

Share
Download
NEC Express5800/110Ge User Manual Download Page 288

D-12  Installing Windows Server 2003 x64 Editions

Updating the System - Applying Service Pack -

Update the system in the situation below:

„

 

CPU is expanded (expanded to single processor to multi-processor).

„

 

Modified system configuration.

„

 

Recovered the system using recovery process.

The system update brings the correction program provided by Microsoft to be applied to reinforce
the system security. The system update is recommended.

It is necessary to use ServicePack2 or more. ServicePack 2 need not be applied again when
Windows Server 2003 x64 Editions CD-ROM where ServicePack 2 is included is used and it is
installed.

If you install Windows Server 2003 x64 Editions CD-ROM which contains Service Pack 2, you do
not have to apply "Hotfix for Windows x64" or "Hotfix for Windows Server 2003 (KB921411)".

Go on the section of "Updating the System".

Perform "Updating the System" and application of the "Hotfix (KB921411)".

IMPORTANT:

 In the situation below, make sure to apply "Updating

the System" and "Hotfix (KB921411)".

„

 

Modified system configuration

„

 

Recovered the system using recovery process.

NOTE:

 If you use Windows Server 2003 x64 Editions CD-ROM

which includes Service Pack 2, the application of "Hotfix (KB921411)"
is not required.

Summary of Contents for Express5800/110Ge













































































































































































































































































































































Reviews:

No comments