manualshive.com logo in svg

NEC Express5800/110Ge, User Manual, Page: 193 / 332

Share
Download
NEC Express5800/110Ge User Manual Download Page 193

Troubleshooting  8-15

The system displays the message below and fails to log on.

Windows Product Activation

This copy of Windows must be activated with Microsoft before you can
continue. You cannot log on until you activate Windows.

To shut down the computer, click Cancel.

YES

NO

Cancel

→

In Windows Server 2003, the above message will be displayed if you use the
operating system without executing the license authentication. Select "Yes", and
execute the procedure for license authentication.

Cannot install the operating system correctly.

T

Did you confirm the notes on installing the operating system?

→

See Chapter 6.

During installation, the following warning is registered in the System Log of the EventViewer:

Error detected on the device \Device\CdRom0
during the paging operation.

→

There is no problem on this issue.

Fail to start the OS:

T

Is the NEC EXPRESSBUILDER DVD in the optical disk drive?

→

Take out the NEC EXPRESSBUILDER DVD and restart the server.

T

Is the OS broken?

→

Use recovery process to recover the system.

The OS presents unstable operation:

T

Did you update the system?

→

Installing a network drive after installation of the OS may cause unstable
operation. Use the NEC EXPRESSBUILDER DVD to update the system. (See
Chapter 6.)

The system does not restart automatically when a stop error occurs, though the system is
adjusted to automatically restarting:

→

When the system does not restart automatically, restart it manually.

Summary of Contents for Express5800/110Ge













































































































































































































































































































































Reviews:

No comments