NEC 1232 Operation Manual Download

Page: 78 / 86

Other Features

Press key.

Press .

Dial extension No. (e.g. 12)

Press to accept.

Press to cancel the pre-set time. (1 short beep tone
shall be sent.)

Return to the idle condition automatically.

Lift handset.

Dial function code.(e.g. 959 or 059)

Hang up.

Dial Block/Wakeup Call Status Confirmation

The setting status of Dial Block and Wakeup Call at each extension can be confirmed at DSS console paired
with Attendant extension (No.10).

Press key.

Press DSS key. The display shows the status.

Press key to return to the idle condition.

Room Monitor

Room Monitor lets one extension monitor (listen to) the sounds in a room containing another extension.

Off-hook condition. (Busy tone is heard.)

Note) KTS can be monitored by only KTS in another method. Refer to “Room Monitor” on Page 39.

Lift handset.

Dial the monitored SLT extension No. (Busy tone is heard).

Press .

1. Replace the handset.

Attendant Call

Attendant Call allows extension user to call attendant extension by dialing a single digit.

Lift handset or press .

2. Press .

1. Lift handset.(Intercom Dial Tone shall be heard.)
2. Press or .

Note: In case, the SLT user cannot access some features after lifting handset.

∗
∗

(Extension No.10 only)

OPAC

To cancel Wakeup Call:

(Extension No.10 with
DSS console)

CHECK

CLEAR

To check the status of Wakeup

call and Dial Block:

To activate Room Monitor at

Monitored

extension:

To activate Room Monitor
at monitoring extension:

To cancel Room Monitor

at monitored and

monitoring extension:

SPK

To place an Attendant

Call:

Summary of Contents for 1232























































































Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands

NEC 1232, Operation Manual

Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands