NEC 1232 Operation Manual Download | Manualshive

Page: 34 / 86

background image

Intercom Outgoing Call

28

Intercom Call

Intercom Call allows extension-to-extension conversation. The system can be programmed for one of two
Intercom Signaling modes: ringing or voice announce. When voice announce is programmed, an Intercom
call signals the called extension with a beep (not ringing). After the beep sounds, the caller can make a voice
announcement over the speaker of the called extension.
Regardless of the signaling mode programmed, an extension user can change it on a per call basis. For
example, a ringing Intercom call can be changed to a voice announced call by dialing a code.

1. Lift handset or press key.
2. Dial extension number.

- To convert a ringing call into a voice announced call,

or vice versa, dial 1.

1. Lift handset.
2. Dial extension number.

- To convert a ringing call into a voice announced call,

or vice versa, dial 1.

Note: Call Monitor, Speakerphone and Single Step Access provide ways to place Intercom Calls without lifting

the handset.

Direct Station Selection

Direct Station Selection (DSS) provides an extension user with one-button access to other extensions in the
system. Each of the ten One-Touch keys on a key telephone can be programmed to call a particular
extension. The One-Touch keys can also be programmed to access any Page Zone (see Paging) using the
steps below.

1.

Lift handset.

2.

Press key.

3. Press     .
4. Dial        .
5. Press            key.
6. Dial extension number.

or

to program a Page Zone, dial 80 - 85.
to program a Doorphone, dial 88 or 89.

7. To program more keys, repeat steps 3-6.
8. Hang up.

1. Lift handset. If Single Step Access is programmed and the

phone is equipped with a Speakerphone, this step can be
skipped.

2. Press key set as DSS key.

To place an Intercom Call:

To program a One-Touch key

for DSS:

To use a DSS key:

SPK

DC

#

One-Touch

One-Touch

ICM

«
...
32
33
34
35
36
...
»

Summary of Contents for 1232























































































Reviews:

No comments

Related manuals for 1232

Brand: DAB Pages: 8

Brand: Samsung Pages: 32

Brand: Uniden Pages: 6

AMERICAN STARPOWER X2

Brand: Nady Systems Pages: 2

Brand: Raymarine Pages: 62

Brand: JRC Pages: 110

Brand: Radio Shack Pages: 32

Brand: Uniden Pages: 40

Brand: Aiwa Pages: 80

Brand: TIE Pages: 28

Port-O-Rotary Phone

Brand: Sparkfun Electronics Pages: 2

Brand: EMPORIA Pages: 16

Unity OpenStage M3 Ex

Brand: Atos Pages: 104

Passport Event Series 2

Brand: Fender Pages: 44

Brand: GE Pages: 2

Brand: Blaupunkt Pages: 63

Brand: AEG Pages: 204

Brand: Philips Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands