NEC 1232 Operation Manual Download

Page: 71 / 86

Other Features

Lift handset or press .

Dial .

- If Busy, voice paths may be occupied, or user operates

at extension other than #10.

3. Dial VAU Message No. (01-25) (See Note)
4. Dial . (Recording and timer counting start.)
5. Record a message from handset or microphone.

- If Busy; user dials Message No. other than specific No.

6. Dial . (Recording and timer counting finish.)

Return to Step 3.

- If user dials “#” instead of "

∗

", recording contents will

not be recorded and Dial Tone may be sent.

Hang up or press .

- When user hangs up or presses SPK without dial

∗

or #,

the recorded message will be saved.

- When 16 sec. has passed during message recording,

timer counting will automatically be finished and the
recorded message will be saved.

Note: Ask your supplier for which types of message you should record in Message No. 01-25.

Lift handset or press .

Dial .

- If Busy, VAU unit is not inserted in the system., or

user operates at extension other than #10.

3. Dial VAU Message No. (01-25).
4. Dial . (VAU Message is erased.)

When erasing finished, Dial Tone may be sent.

- If Busy, user dials Message No. other than specific No.

Hang up or press .

Lift handset or press .

Dial .

- If Busy, Voice Paths may be occupied, or user operates

at extension other than #10.

Dial VAU Message No. (01-25).

- If user dials VAU Message No. which was not recorded,

Dial Tone may be sent.

4. Dial .
5. Playback the message from handset or built-in speaker.

- If Busy, user dials Message No. other than specific No.
- When recorded contents has been finished, 1-beep tone

will be sent.

After confirmed, return to Step 3.

6. Hang up or press .

To record a VAU Message:

To erase a VAU Message:

To confirm a VAU Message:

(Extension No.10 only)

SPK

∗

SPK

∗

SPK

∗

SPK

Summary of Contents for 1232























































































Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands

NEC 1232, Operation Manual

Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands