NEC 1232 Operation Manual Download

Page: 49 / 86

Alphanumeric Display TEL Features

DND Message

DND Message send a message to a calling extension when your telephone activated DND for Intercom calls.

1. Press .

2. Dial message number (00-49), dial          .
or
Press            key No.1 or No.2 for personal message, then
dial          .

- DND flashes intermittently as confirmation.

1. Press and .
2. Edit message by Message Edit Mode.
3. Press and . DND flashes intermittently as

confirmation.

1. Press .

1. Press and .

- When DND message is activated, DND flashes

intermittently.

Leave Message with MW

When you make an Intercom call to display phone and receive a busy signal or no answer, you can leave a
text message with Message Waiting (MW).

1. Place Intercom call. Busy or no answer.
2. Dial . Indicator flashes intermittently as

confirmation.

- Display shows "LEAVE MESSAGE ?", then you can

enter a message. If you replace handset after this step
operation, it is simple message waiting procedure.

3. Dial .
4. Dial message number (00-49), dial .

or
Press            key No.1 or No.2 for personal message, then
dial          .
or
Press          , edit a message by Message Edit Mode, then
press    again and dial    .

- A text message is left on called display phone.

To set DND message using

preset messages:

To set DND message that edited

by Message Edit Mode:

To cancel message on the

telephone:

To activate/cancel previous

message on the telephone (last

time you set message for DND):

To leave a Message:

TRFR

One-Touch

TRFR

FLASH

TRFR

CLEAR

One-Touch

FLASH

∗

Summary of Contents for 1232























































































Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands

NEC 1232, Operation Manual

Search results

Summary of Contents for 1232

Reviews:

Related manuals for 1232

Brands by name

Popular brands