NAL A3LA-RM User Manual Download

Page: 43 / 172

AL3A-RM User Guide Version B

Document Number: 451-93156-002B

43 of 172

Asynchronous operation with error correction (acknowledged mode)

(default)

B.16

–

DSR

VERRIDE

Define the behavior of DSR.

DSR always active (default)

Same as 0

B.17

–

IEW

CTIVE AND

TORED

ONFIGURATION

View the current active configuration and stored profiles.

B.18

–

TORE

CTIVE

ONFIGURATION

Store the active profile in non-volatile memory. This is used to store user

configurations for later use.

Store current (active) configuration as profile 0

Store current (active) configuration as profile 1

B.19

–

ESIGNATE

EFAULT

ESET

ROFILE

Select profile for use after power-up.

Select profile 0 (default)

Select profile 1

B.20

–

ONTROL

REAK

Control the response of the A3LA-RM to a break received from the DTE or the remote

modem according to the parameter specified. The response is different in three

separate states:

When a break is received from DTE when A3LA-RM is in data transfer mode:

Enter in-call command mode, no break sent to remote modem

Clear data buffers and send break to remote modem

Same as 0

Send break to remote modem immediately

Same as 0

Summary of Contents for A3LA-RM













































































































































































Search results

Summary of Contents for A3LA-RM

Reviews:

Related manuals for A3LA-RM

Brands by name

Popular brands

NAL A3LA-RM, User Manual

Search results

Summary of Contents for A3LA-RM

Reviews:

Related manuals for A3LA-RM

Brands by name

Popular brands